-
Autoclaved aerated concrete block is a new type of wall material with energy saving, waste recycling and environmental protection. Autoclaved aerated concrete blocks have the advantages of light weight, heat insulation, sound insulation, heat preservation, fire prevention, earthquake resistance, easy cutting, etc. At the same time, autoclaved aerated concrete blocks also have high water absorption and slow water absorption
Published on: August 8, 2022 Clicks: 72
-
The number of cracks in autoclaved sand aerated concrete wall is more than that in shale modulus brick wall, but much less than that in fly ash brick wall. The main reasons and corresponding preventive measures are: 1. The drying shrinkage of autoclaved aerated concrete blocks is too large, and autoclaved sand aerated concrete blocks are cured by high-pressure steam, which has greatly reduced the shrinkage value of products. However, due to its composition and structure
Published on: July 29, 2022 Number of hits: 66
-
What are the differences between autoclaved aerated concrete blocks and concrete bricks? The wall materials used in the construction market before were mainly red bricks (clay bricks). At present, the state restricts the use of solid clay bricks as filling materials for frame structures in urban construction, and prohibits the use of solid bricks with strength grade below MU10 in buildings with more than 5 floors. 1、 Properties of autoclaved aerated concrete blocks
Published on: April 12, 2021 Clicks: 690
-
Interpretation of the reasons for the uneven thickness of materials in the autoclaved aerated concrete block production line, grinding materials to the required particle size for production is an important part of the aerated concrete block equipment. In this regard, ball mills play an important role. We found that in the production process, the grinding of materials is insufficient and the thickness is uneven. There are many reasons for this phenomenon. The following concrete aerated brick manufacturers will help us
Published on: 2021-05-24 Number of hits: 252
-
What are the measures to prevent the wall cracking of aerated concrete blocks? Before plastering the aerated concrete block wall, clean up the floating soil and floating plaster on the block surface, repair the missing edges and corners and the mortar is not full with mixed mortar, wet the wall the day before plastering, spray (or brush) once with mortar interface agent or 108 glue before plastering, and before there is no obvious crack on the surface after plastering
Published on: November 4, 2019 Clicks: 202
-
Aerated concrete is a kind of stone that can float on the water - some people call it pumice! Autoclaved aerated concrete block manufacturer will show you more knowledge! The pores in the middle make this material very light - also known as light bricks and light walls - and also make this material block sound - also known as sound insulation brick, sound insulation brick; Because this material contains a lot of
Published on: December 6, 2020 Number of hits: 96
-
Autoclaved aerated concrete block manufacturers take you to learn more! Autoclaved aerated concrete blocks: with fly ash, lime, cement, gypsum, slag, etc. as the main raw materials, they are made by steam and other processes under the pressure of mixing, pouring, static, cutting, etc. according to the composition, participating in an appropriate amount of gas generators, regulators, bubble stabilizers. Features: As a new type of wall filling data,
Published on: September 6, 2019 Clicks: 205
-
The manufacturer of autoclaved aerated concrete blocks introduces the product classification, technical requirements, test methods, inspection rules and product quality specifications, as well as the stacking and transportation of autoclaved aerated concrete blocks. This standard is applicable to autoclaved aerated concrete blocks for civil and industrial building walls and thermal insulation materials. Autoclaved aerated concrete blocks are made of fly ash, lime, cement, gypsum, slag, etc
Published on: August 20, 2019 Number of hits: 166
-
The manufacturer of autoclaved aerated concrete block introduces that autoclaved aerated concrete block is a kind of porous concrete product made of fly ash, lime, cement, gypsum, slag, etc. as the main raw materials, with appropriate amount of air entraining agent, conditioner, bubble stabilizer, and through the process of batching, mixing, pouring, static stop, cutting and high-pressure steam curing. The construction characteristics of autoclaved aerated concrete blocks are also very excellent
Published on: February 19, 2020 Number of hits: 294
-
The manufacturer of autoclaved aerated concrete block introduces that autoclaved aerated concrete block is a solid block composed of cement, slag, sand, lime, etc. as the main raw materials to participate in the air entraining agent, which is formed by mixing and autoclaved curing. Its characteristics are: light weight, only 500~600kg/m3 for Grade 05.06; High compressive strength, up to 3.5~7.5Mpa, good thermal insulation performance
Published on: August 13, 2019 Clicks: 203
-
The manufacturer of autoclaved aerated concrete block introduces that autoclaved aerated concrete block is a kind of porous concrete product made of fly ash, lime, cement, gypsum, slag, etc. as the main raw materials, with appropriate amount of air entraining agent, conditioner, bubble stabilizer, and through the process of batching, mixing, pouring, static stop, cutting and high-pressure steam curing. 1. Light weight: dry bulk density of different grades of the product
Published on: August 8, 2019 Clicks: 182
-
Autoclaved aerated concrete block manufacturers introduce that autoclaved aerated concrete is a general term, which can be divided into sand aerated and ash aerated according to the original data "Sand" and "ash" refer to silicon oxide, one of the main raw materials. Sand refers to the use of quartz sand to provide silicon oxide, and ash refers to the use of fly ash to provide silicon oxide. Generally speaking, sand aerated concrete
Published on: August 6, 2019 Clicks: 717
-
The manufacturer of autoclaved aerated concrete block introduces that autoclaved aerated concrete block is a kind of porous concrete product made of fly ash, lime, cement, gypsum, slag, etc. as the main raw materials, with appropriate amount of air entraining agent, conditioner, bubble stabilizer, and through the process of batching, mixing, pouring, static stop, cutting and high-pressure steam curing. Aerated concrete block is the lighter type of concrete,
Published on: August 1, 2019 Number of hits: 252
-
Instructions for aerated concrete block masonry 1. Autoclaved aerated concrete block manufacturer shall stop block arrangement design in building construction to facilitate batching and reduce on-site sawing workload. 2. Before building the wall, spray proper amount of water to the block. The watering amount of water should be 8-10mm deep into the block. 3. The masonry mortar should be N5 mixed mortar
Published on: March 18, 2020 Number of hits: 107
-
1. Autoclaved aerated concrete blocks are mainly used for external infill walls and non load bearing internal partitions of buildings, and can also be combined with other materials to form a composite wall with thermal insulation function, but should not be used for the outer layer. 2. Autoclaved aerated concrete blocks should not be used in the following parts without effective measures: building elevation below ± 0.000; Long term immersion and frequent dry wet handover
Published on: July 20, 2019 Number of hits: 97
-
Autoclaved aerated concrete block manufacturers introduce that autoclaved aerated concrete is a general term, which can be divided into sand aerated and ash aerated according to the original data "Sand" and "ash" refer to silicon oxide, one of the main raw materials. Sand refers to the use of quartz sand to provide silicon oxide, and ash refers to the use of fly ash to provide silicon oxide. Generally speaking, sand aerated concrete
Published on: July 19, 2019 Number of hits: 152
-
The manufacturer of autoclaved aerated concrete block introduces that autoclaved aerated concrete block is a kind of porous concrete product made of fly ash, lime, cement, gypsum, slag, etc. as the main raw materials, with appropriate amount of air entraining agent, conditioner, bubble stabilizer, and through the process of batching, mixing, pouring, static stop, cutting and high-pressure steam curing. The unit volume weight of autoclaved aerated concrete block is
Published on: July 12, 2019 Clicks: 110
-
The manufacturer of autoclaved aerated concrete block introduces that the autoclaved aerated concrete block is economical and environmentally friendly according to the function of partition wallboard, roof panel, exterior wall panel, floor slab and other functional plates. Application range of autoclaved aerated concrete blocks: applicable to non seismic areas and areas with seismic fortification intensity of 6 to 8 degrees; It is applicable to the internal partition walls of middle grade buildings, middle grade and higher grade buildings; Applicable to all kinds of steel
Published on: July 5, 2019 Number of hits: 77
-
The manufacturer of autoclaved aerated concrete block introduces that the unit volume weight of autoclaved aerated concrete block is one third of that of clay brick, its thermal insulation performance is 3-4 times that of clay brick, its sound insulation performance is twice that of clay brick, its impermeability is more than twice that of clay brick, and its fire resistance is 6-8 times that of reinforced concrete. The construction characteristics of autoclaved aerated concrete block are also very excellent, and it cannot
Published on: July 4, 2019 Number of hits: 219
-
Light brick partition wall refers to a non load bearing wall for building partition formed by using light bricks or light blocks with special adhesives. Because of its light weight, high strength, water resistance and impermeability, sound insulation and fire prevention, thermal insulation, green environmental protection, and fast construction, it has been subject to the national wall reform policy for many years
Published on: June 25, 2019 Number of hits: 104
-
As a new type of building material, sand aerated block has the advantages of light weight, good thermal insulation performance, earthquake resistance, etc., and is vigorously promoted and used by the country. The aerated block is made of a variety of mixtures, and its raw materials are very rich, with good social and economic effects
Published on: June 25, 2019 Clicks: 184
-
Since the reform and opening up, the domestic economy and people's life philosophy have undergone tremendous changes. The income level of the Chinese people has greatly improved, and their living conditions are also constantly improving. Now people live in western-style houses, in various elegant neighborhoods, and gradually begin to have environmentally friendly, economical, and fast living
Published on: June 25, 2019 Number of hits: 278
-
Autoclaved aerated concrete product itself is a new type of lightweight and porous building material, which has good sound insulation and heat insulation properties, as well as a new type of wall material without radiation and durability. The vertical mortar joints of the upper and lower blocks of the aerated concrete block wall should be staggered, and the staggered length should be 3
Published on: June 25, 2019 Number of hits: 230
-
Shenyang aerator manufacturer reminds you that in order to avoid cracks in the aerator, we should pay attention to the following aspects during the construction design: 1. When the wall length exceeds 5m, the wall should be set
Published on: June 25, 2019 Clicks: 126
-
Sand aerated block is a new type of environmental protection material, which is used more and more in building construction. The production of aerated block requires professional production equipment, but the noise of such equipment is generally high. I believe many people are very worried about this problem. Today, let's see how to
Published on: June 25, 2019 Number of hits: 116
-
Sand aerated block is a kind of environment-friendly building material now. We may not see many of them in ordinary times, but does it sound inconceivable to those who need additives in the manufacturing process of aerated block? Not only food, but also building materials. Don't worry
Published on: June 25, 2019 Number of hits: 104
-
Today, Shenyang aerated brick manufacturer will introduce you what is fly ash aerated brick. 1. Volume weight fly ash roof thermal insulation aerated concrete is a kind of building product with porous structure. Light volume weight is one of its main characteristics, and the weight can be controlled by air entraining agent. Fly ash roof insulation, aerated coagulation
Published on: June 25, 2019 Number of hits: 68
-
Gas dispensing blocks have been more and more used in the construction industry. Because they are environmentally friendly building profiles, and because they are light and environmentally friendly, some points that need attention in the use process may be ignored if you do not pay attention. Qin Zhen, the manufacturer of Shenyang gas dispensing blocks, reminds you that although they are
Published on: June 25, 2019 Clicks: 132
-
There are many processes in the whole production process of the complete set of aerated brick equipment. How long does the aerated brick equipment need steam curing in production and is it the best? The steam curing of the billet is carried out in the autoclave. The suitability of this process and the best time to steam these are the key points that all brick factories need to consider. If not properly autoclaved, the air block will not achieve its original excellent effectiveness
Published on: June 25, 2019 Number of hits: 387
-
In the construction of aerated bricks, it is impossible that there are no problems at all. So today's mini editor summarizes several common faults and solutions in the construction of aerated bricks. Let's take a look! As autoclaved aerated concrete blocks have not been widely used in China for a long time, the production capacity of various places is not concerned, and some projects are tight,
Published on: June 25, 2019 Number of hits: 111
-
Autoclaved aerated concrete product itself is a new type of lightweight and porous building material, which has good sound insulation and heat insulation properties, as well as a new type of wall material without radiation and durability. All indicators of Qin Zhen's environmental protection products are superior to the national standards, and can constantly meet the customized needs of customers
Published on: June 25, 2019 Number of hits: 165
-
Since the reform and opening up, the domestic economy and people's life philosophy have undergone tremendous changes. The income level of the Chinese people has greatly improved, and their living conditions are also constantly improving. Now people live in western-style houses, in various elegant neighborhoods, and gradually begin to have environmentally friendly, economical, and fast living
Published on: June 27, 2019 Clicks: 184
-
1、 Autoclaved aerated concrete blocks always have good functions in application, so people will choose to use them in many times to meet their requirements, and people will always meet their quality in application. When we need to select suitable bricks, we need not only consider bricks
Published on: June 25, 2019 Number of hits: 102
-
Congratulations on the official website of Liaoning Qinzhen Environmental Protection Building Materials Co., Ltd. and Kaihong Technology Cooperation officially launched in June 2019! Liaoning Qinzhen Environmental Protection Building Materials Co., Ltd., founded in 2012, is located in the Lighthouse of Liaoning Province
Published on: June 25, 2019 Number of hits: 276
-
Today, we will explain the difference between light brick and red brick. Is red brick better or light brick better? Red brick (solid clay brick) is made of clay, shale, coal gangue and other raw materials after crushing, mixing, kneading, manual or mechanical pressing, and then dried and placed in 900 shots
Published on: January 16, 2019 Number of hits: 145
-
There are two main types of application in the building system: the first type is the multi-storey mixed structure, which mainly gives play to the advantages of good thermal insulation performance of aerated concrete. Under the condition that the original horizontal bearing system of multi-storey buildings remains unchanged, it is the most economical thermal insulation method among similar systems to use it as an external wall material as well as thermal insulation material. The second type is the reinforced concrete frame structure system
Published on: January 16, 2019 Number of hits: 234
-
Aerated concrete block is a new type of building material with light weight, porous, heat insulation, good fire resistance, nailing, sawing, planing and certain seismic capacity. As early as the early 1930s, China began to produce this product, and it is widely used in Shanghai International Hotel, Shanghai Tower, Fuzhou
Published on: January 16, 2019 Number of hits: 252
-
Through the observation of the production process of lightweight concrete, the following problems mainly exist in the mixing of lightweight concrete: 1. The density of foam and cementitious material is 200~300kg/m ³ Left and right lightweight concrete, the total volume of foam can really account for 70%~8% of lightweight concrete
Published on: January 16, 2019 Number of hits: 164
-
Autoclaved aerated concrete blocks have good workability. Able to saw, plane, nail, mill and drill. And reinforcement can be added during manufacturing. It brings great convenience and flexibility to the construction. When the temperature of aerated concrete is below 600 ℃, its compressive strength increases slightly. When the temperature is about 600 ℃, its compressive strength is close to that of normal temperature
Published on: January 16, 2019 Number of hits: 270
-
In 2019, in order to meet the current requirements for building construction accuracy in Liaoshen area and improve product quality, the company invested another 2 million yuan for equipment technical transformation, ensuring that the products produced meet and exceed national standards, and established a more stringent enterprise to meet the market requirements for high-precision blocks
Published on: January 16, 2019 Number of hits: 334
